OBD read and write is 50/50 chance. Some read/write via OK no problem.
Some obd read ok, failed to write by OBD.

Some obd read no problem, write it back it goes super fast to 100%, but back an error and car won’t start.

So better read and get password via OBD, then boot to write. 
And see instructions doesn’t need resistors.  Better have a battery maintainer. It needs lots of power.
SIEMENS CONTINENTAL SID209 [ TC1797 INT.F.] – Ford

Step 1: Password Search
Connect the pinout and use the following driver:
Use the driver:
→ TOOLS BOOT MODE
→ INFINEON TRICORE Tool Password
→ OBD PASSWORD SID209 FORD
→ Click on “Find Password” and follow the software messages.
Attention: If you cannot find the password from Pinuot, you must launch the driver in OBD on the vehicle.

Step 2: Read and Write ECU

Connect with the multifunction cable the following pinout and the boot shown below
Use the foxflash driver:
→ TOOLS BOOT MODE
→ INFINEON TRICORE Boot
→ SAK TC1797

see instructions doesn’t need resistors.

Full Read and Write Toyota Denso NEC76F00XX BDM Success

* Denso NEC76F0039AGD 211941-46000930 Toyota

* Denso NEC76F0039AGD 275036-1152 Fujitsu Toyota

* Denso NEC76F0039AGD 275036-3740 Toyota

* Denso NEC76F0039AGD 275036-9050 Toyota

* Denso NEC76F0039AGD 275036-9170 Toyota

* Denso NEC76F0039AGD 275136-1910 Toyota

* Denso NEC76F0039GD 175822-737 Toyota

* Denso NEC76F0039GD 175822-762 Toyota

* Denso NEC76F0039GD 175822-773 Toyota

* Denso NEC76F0039GD 175822-887 Toyota

* Denso NEC76F0039GD 275036-1150 Toyota

* Denso NEC76F0039GD 275036-1152 Toyota

* Denso NEC76F0039GD 275036-6941 Toyota

* Denso NEC76F0039GD 275036-7780 Toyota

* Denso NEC76F0039GD 275036-9160 Toyota

* Denso NEC76F0040AGD 175822-652 Hino

* Denso NEC76F0040AGD 175822-887 Toyota

* Denso NEC76F0040AGD 211841-3581A830 Toyota

* Denso NEC76F0040AGD 275036-9170 Toyota

* Denso NEC76F0040AGD 275922-856 Toyota

* Denso NEC76F0040GD 175822-666 Toyota

* Denso NEC76F0040GD 175822-887 Toyota

* Denso NEC76F0040GD 275036 6941 Toyota

* Denso NEC76F0040GD 275036-2050 Toyota

* Denso NEC76F0040GD 275036-7341 Toyota

* Denso NEC76F0040GD 275036-7780 Toyota

* Denso NEC76F0040GD 275036-9170 Toyota

* Denso NEC76F0070 275036-3410 Toyota

* Denso NEC76F0070 275036-3560 Toyota

* Denso NEC76F0070 275036-5130 Toyota

* Denso NEC76F0070 275036-5920 Toyota

* Denso NEC76F0070 275922-001 Toyota

* Denso NEC76F0070 275992-428 Toyota

* Denso NEC76F0070 276122-092 Toyota

* Denso NEC76F0085 211941-45800932 Toyota

* Denso NEC76F0085 275036-5280 Toyota

* Denso NEC76F0085 275036-5650 Toyota

* Denso NEC76F0085 275036-5810 Toyota

* Denso NEC76F0085 275036-6110 Toyota

* Denso NEC76F0085 275036-7400 Toyota

* Denso NEC76F0085 275036-7581 Toyota

* Denso NEC76F0085 275922-022 Toyota

* Denso NEC76F0085 275922-320 Toyota

* Denso NEC76F0085 275922-473 Toyota

* Denso NEC76F0085 275922-500 Toyota

* Denso NEC76F0085 275922-532 Toyota

* Denso NEC76F0085 275922-828 Toyota

FoxFlash is Very easy to use and works as described. Definitely would recommend buying from this company.

---

The FoxFlash are pretty nice, powers up very fast, it is definitely good for professional use.

---

2023 Foxflash ECU Programmer Review: Read/ Write/Checksum OK
edc15 P+ BENCH Flash & eeprom Start

EDC15C3 (bench)– from Renault Laguna/ Read/Write OK

EDC15C13 (bench) — from Espace IV/ Read/ Write OK

EDC15C4 Full Flash R/W OK – obd-bench with 12v

edc15c13 renault BENCH Flash&eeprom Start

EDC16C1 E+F R/W OK – bench ok.

EDC16C9 bench R/W OK

EDC16C10 Read ok, Write ok, Checksum

Edc16c31 bmw bench r/w ok chck ok

EDC16CP31 BENCH DPF OFF R/W PERFECT

EDC16C3 R/W OBD CHECK OK

EDC16CP33 R/W OBD CHK INJCODE OK

Edc16c34 program disable while uploading, reads ok.

edc16u34. it worked reading and writing bench

EDC16CP35 READ/WRITE OK

EDC16C34 R/W OK Hardcut added & Car started perfectly psa

Edc16c39 can Read and write ok with obd Opel zafira B 1.9cdti 150cv

Edc16c39 fiat ducato obd R/W checksum ok

edc17c06 bmw BENCH, Read ok, Write ok, Checksum ok, car starts

edc17c08 bench ok

Edc17cp20 vag bench r/w ok chck okEcd17c70 obd ok

Edc17cp20, VR ok, write ok vw t6

Esc16c60 bench ok password unlock

EDC17CP01 V6 CDI Sprinter r/w ok bench

EDC7C3 bench r/w ok man bench

EDC17CP06 E+F R/W OK – bench

Edc17cp09 read/write ok chk ok

EDC17C10 Read ok, write OK, checksum ok bench

EDC17C11 bench R/W OK

EDC17Cp39 on Freelander 2 obd read write chk ok

EDC17C41_TC1797_ Bench bed written ok bmw

Edc17cv41 r/w cks ok.

edc17c42 bench R/W ok

Edc17cp44 bench read and write ok

EDC17CP45 BMW X6 D40 bench reading ok

edc17cp45 – “reading” (it is VR) via OBD. No file on DB but ID is working

Edc17c46 R/W bench OK!

edc17c50 TC 1797 BENCH r/w OK Mod Stage 1 with Display Calibration

EDC17CP54 on bench r/w all fine and easy. Cheksum with Winols.

Edc17c56 read ok Bench

edc17c59 BENCH Read ok, write OK, checksum ok opel

edc17c60 psa bench r/w ok

EDC17C64 bench R/W OK

Edc17c66 Mercedes r/w ok bench

Edc17c69 Iveco bench r/w ok chck ok

EDC17C79 Jeep Grand Cherokee full RW include checksum works OK

Edc17c84 r/w ok bench

EDC17C84 Opel vivaro 2018 with system adblue. with module 71

Delphi DCM3.5 R/W OK in JTAG

Dcm6.1 ford(psa) obd r/w ok chck ok

Dcm 6.2 obd ok

DCM6.2V Audi A3 2017 VR/Write ok

Dcm 7.1 boot ok

Crd2 Mercedes not work- read obd WRITE OBD FAIL- r/w ok by jtag

CRD3.10 Full bench read/write (flash+eprom) + auto checksum

Simos 8.10  obd  or boot car not start ecu problem

MEV17.4.2 READ MOD WRITE

ME 7.5 Full R/W , Stage1 all OK

Me7.6.2 opel bench r/w chck ok

ME7.6.3 Bench reading ok

MED9.1 bench R/W OK

medc17 bench R/W ok

MED17.2.5 R/W Ok Seam’s like a stable & Reliable tool, very Internet dependant.

Med 17.5.5 VW Scirocco 1.4 TSI 160CV Bench R/W – OK!

Med 17.7.7 Mercedes r/w ok bench

ME 17.9.6 read flash + eeprom ok

PCR2.1 Read MCU ID, ,Bench mode R/W, Online Patch unlock OBD, Checksum

MD1CP001 MB W213 2018y R/W OK , checksum calculated from the original file.

MD1CP014 bench r/w ok

MD1CS004 read + write OK audi

md1cs003 psa bench ok

Md1cs006 renault r/w ok bench

Mg1cs201 r/w bench ok

Mg1cs003 r/w bench ok

SID201 via OBD, success EGR OFF, read/write + checksum ok

sid206 obd read/write ok

Sid208 r/w ok

SID211 OBD OBDFORD TRANSIT ok

SID 305 tricore 1766 Micro Read/Write Boot Mode ok STG 1 DPF, EGR, DTC OFF.

SID310 READ PASSWORD, READ FLASH,READ EEPPROM, DTC OFF, FLASH WRITE, CHECKSUM

Sid803A PSA full system Clone done. Read in 15min, Write in 15min, Car Start

SID807 evo obd read ok, write mod ok. CHK MANUAL, program did not ask if it should correct or not

PCR2.1 obd vr/unlock/w ok

E83 full mode R/W dtc off, CS ok with ori file

E97 full system R/W ok

E98 bench r/w ok

MB175800 Denso Works Perfectly:)

---

Fiat 500 MARELLI  IAW 9GF read/write with foxflash successfully on bench in car.

MARELLI 9GF – Fiat, Alfa Romeo, Lancia [Gasoline] bench pinout to foxflash

read, write ok, checksum by tool.

 

---

Because the FoxFlash is working very good for me.  I decided to make this review of facts and tested procedures.

• It works only with the device connected to USB port, like the others. You won’t run the software without it.
• You need some electronic skills to work with it since there is very minimalistic GUI of the software and also you need to make some repairs to the device. It is not intended for use with  OBD port users generally. In this case there is a risk of the car damage if you mess around this port without a basic knowledge.
• In majority of cases you do not need to open ECUs like before and this is the best benefit of this device.

Got it several months now and worked well on :

EDC16U1 bench full read and write
EDC16U34 bench full read and write
EDC16U31 vw – the crazy additive diesel (BRT) bench full read and write (OBD not possible but KESS v2 worked OK)
EDC17C64 vw bench full read and write
EDC17C46 vw bench full read and write, then tested OBD flash too, only with VR – but finally it also succeeded. Long time WR – 18 minutes
EDC15C2 Suzuki OBD (Flash only)
EASYTRONIC TCM Opel, Ford bench Flash read and write boot
EDC17C56 BMW F25 bench full RW OK *VR file OBD read impossible because file not in database. Anyways who cares about VR.
EDC17C74 Bench full read and write include checksum works OK
EDC17C79 Jeep Grand Cherokee full RW include checksum works OK
SIEMENS PCR2.1 Bench full read and write include checksum works OK
SIEMENS PPD1.2 Bench full read and write include checksum works OK
EDC17CP46 Mercedes BlueMotion Bench full read and write include checksum works OK
EDC17CP04 Audi Q7 CASA engine Bench full read and write include checksum works OK
EDC16C39 Hyundai Bench full read and write include checksum works OK, OBD read tested too OK, (special thanks to fellow member mb055 helping me out with the SW)
EDC17C57 Hyundai I30 – Bench full read and write include checksum works OK
TCM ZF 9HP Jeep, Fiat, Dodge – BDM full read and write include checksum works OK.
DELPHI MT80  (Geely, Chevrolet) full read boot / warning there is a mistake in the circuit hint. Solved, works fine now.
DENSO with NEC76F0038GD 175822-773 Toyota  – FULL JTAG read and write OK.
SIEMENS SID801 – Citroen Berlingo – BENCH read and write both FL+EEP works like a charm
TCM DCT250 DC4 – Getrag, renault DSG – Bench full read and write include checksum works OK
EDC16C34 PSA – bench full read and write

EDC17C60 read and write Bench checksum by tool GOOD
EDC17C10 read and write Bench checksum all OK

---

Bmw Edc17c50

Bmw Edc17c50.. Read and write on bench… Cheksum by myself

RENAULT
Hi all
Renault trafic 2 2.0dci 115hp 2013
✅ R/W OBD
 

VW TIGUAN 2015

VW TIGUAN 2015
 EDC 17 C46
 rw/wr bench
 ckx by fox

SEAT IBIZA 2012

1.6 TD SIMOS PCR 2.1
ID DETECTED——-OK
EEPROM FLASH LOCKED —–OK
READ LOCKED BY OBD ——–OK
WRITING MOD FIILE UNLOCKED FLASH ——-OK
ALL TIME 25-30 min
THANKS FOXFLASH

excelenct very great tool for me

Dacia Lodgy 2016

 Dacia Lodgy 2016
 bench metod
 rw/wr ok
 cks by Fox

Ford MD1CS005

Bench
Read OK
Write OK
Chk by Fox

Iveco Daily 2.3M-Jet 126ps
Iveco Daily 2.3M-Jet 126ps EDC16C39 ✅OBD Read ✅OBD Write ✅Chk

Godiag GT107+ DSG Plus can work with foxflash ECU programmer to read DQ200 and DQ250 TCU data. It needs to set GODIAG GT107 + analog ignition switch in “manual” mode.

---

Foxflash received,  read and write Mercedes Delphi CRD3PLUS A0 ecu OK ! 

---

Edc17 c46
Edc17 c46 all by obd, virtual read an write, cecksum by tool

Peugeot 208
EDC17C10
R/W bench
all OK
 

foxflash clone Mercedes Benz Siemens SIM4LKE transmission compressor success.

SIEMENS SIM 4L KE [C167] – Mercedes Benz [ Gasoline ]

Pinout

To read and write use the following driver:
→ TOOLS BOOT MODE
→ SIEMENS-INFINEON C167
→ Bosch – Flash 29F800

If the ECU doesn’t enter boot mode, proceed as follows:

→ Switch off the ECU and remove the grey wire.
→ Connect directly to ground the boot pin with a needle.
→ Switch on the ECU.
→ Remove the ground.
→ Launch the driver and click the read / write buttons.

*Some versions of ECUs have the flash locked in writing.

Note:

1. Fgtech galletto v54 clone can kill this ecu during reading – if there is vin in ecu galletto can wipe it out, and coding also.
2.Yanhua ACDP also has module 18 but can only renew SIM4LKE, need to adapt with DAS or Vediamo.