Foxflash arrived very fast , the product was as described, great communication with ERIN , I will test and report

FoxFlash Super ECU tool does the job like it its supposed to.

FoxFlash definitely equipped enough for shop environment. Does everything you could ask for and more. it's already paid for itself in the first hour of use Fiat Marelli MD9F JTAG mode, R/W, chk OK

---

Prompt service easy to use

Customer service was friendly, responsive, and knowledgeable. It saved me the cost of the unit first scan.

Smart 453

ecu me17.9.20 safe write and read 

-Edc17c41 BMW 520d f11 read write bench Manual checksum
-Edc17c50 BMW x3 -13 read write bench manual checksum
-Denso 76F00xx, Toyota auris read write obd checksum by fox
-Denso MB279700, Volvo v60 d4 vea, read unlock bench write obd checksum fox

Citroen jumper dcm7.1b – r/w , and the most asked (yes .. the checksum is made by te tool).

 

Foxflash Read Jaguar MEDC17.9 by OBD success. 

MEDC17.9 OBD is in the foxflash driver list.

But if the ECU has OTP protected, you need to do bench or use breakout to do it via OBD on bench.

For example:

OBD on the bench reading the MEDC17.9 with foxflash programmer+ godiag gt100 breakout box. I want to try and write the modified files via OBD after an OBD read. The ECU data that had been corrupted is now all OK.

I have had an interesting case with this ECU MEDC17.9 that had failed and had the OTP block. I read the Full flash via OBD, had the flash modified to delete CAT/AdBlue/DPF and EGR (use a tuning file service). When I got the modified file back, I decided to write it via Bench mode. I did the checksum correction using the original flash and flashed it via Bench mode 100% without any problems. The car is now starting and has no faults whatsoever and drives very well. We had brought it on a flatbed. Another great success with FoxFlash and a bit of experimenting.

 

---

FoxFlash Read and Write Alfa Marelli MM10JA Success. 

OBD mode:
The built-in OBD does not working. It does not read the ECU ID nor read/write ECU.

Boot mode:
It works fine in boot mode.

---

Foxflash Pinout to FCA CONTINENTAL GPEC4. 

BAM SPC5674 CONTINENTAL GPEC4 FCA Pinout

 

Connect with the multifunction cable the CNF1 on the pcb.

Read and Write ECU

Use the driver:
→ TOOLS BOOT MODE
→ MOTOROLA FREESCALE BAM
→ FCA CONTINENTAL GPEC4

Foxflash read and write Peugeot 2008 year 2019 MD1CS003 on bench successfully.

*** Peugeot 2008 1.5 BlueHDi 100hp ***
*** Year 2019 ***
*** MOTOR CODE YHY ***
*** MD1CS003 Bench mode ***
*** Read/Write/ChecksumBy FoxFlash ***
*** AdBlue OFF ***

---

Foxflash pinout to Siemens SIM2K-341 – Kia [MPCZ561 ECU]

Connect multifunction cable as follows:

Solder the dip/sip connectors on the pcb:

Insert Siemens/Marelli adapter as in photo:

To read and write use the following driver:
→ BDM/ JTAG MODE
→ BDM MPC
→ MPC55x/56x

TO COMMUNICATE WITH THE MICRO TRICORE [TCU] GO TO THE TCU-GEAR SECTION OF THE SOFTWARE.

If it is TC1766 processor, check pinout and instruction below:

Foxflash pinout to Siemens SIM2K-341 – Kia [Tricore TC1766 TCU ]

Kit to use for reading micro Tricore (TCU):
Multifunction cable
4 resistores 560Ω

Connect multifunction cable as follows:

Solder 4 resistores like in figure:

Foxflash Pinout to FCA CONTINENTAL GPEC4

BAM SPC5674 CONTINENTAL GPEC4 FCA Pinout
Connect with the multifunction cable the CNF1 on the pcb.

Read and Write ECU

Use the driver:
→ TOOLS BOOT MODE
→ MOTOROLA FREESCALE BAM
→ FCA CONTINENTAL GPEC4

---

Foxflash Pinout to FCA CONTINENTAL GPEC4LM

Check foxflash pinout to CONTINENTAL GPEC4LM

BAM SPC5674 CONTINENTAL GPEC4LM FCA Pinout

Connect with the multifunction cable the CNF1 on the pcb.

Read and Write ECU

Use the driver:
→ TOOLS BOOT MODE
→ MOTOROLA FREESCALE BAM
→ FCA CONTINENTAL GPEC4LM

---

Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench.

Here is the fox flash pinout to MSM 2.0.

Select driver

Mercedes

Siemens ECUS

1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM

If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below:

After read flash/eprom – Disconnect ecu and restart software (unplug foxflash) – restart Then connect again, Write flash, Also try lower power only need 13v on this ecu. 

The Foxflash ECU Programmer can support FCA GPEC2 GPEC3 GPEC4LM GPEC2A ECUs read and write in Boot mode since March 14, 2023.Click here to check the detailed ECU models. Today we’ll share the Pinout to these ECUs.

• BAM SPC5674 CONTINENTAL GPEC2A FCA Pinout

Connect with the multifunction cable the CNF1 on the PCB.

Use the driver:

→ TOOLS BOOT MODE

→ MOTOROLA FREESCALE BAM

→ CONTINENTAL GPEC2A

 

• BAM SPC5674 CONTINENTAL GPEC3 FCA Pinout

Connect with the multifunction cable the CNF1 on the PCB.

Use the driver:

→ TOOLS BOOT MODE

→ MOTOROLA FREESCALE BAM

→ CONTINENTAL GPEC3

 

• BAM SPC5674 CONTINENTAL GPEC4 FCA Pinout

Connect with the multifunction cable the CNF1 signal on the PCB.

Use the driver:

→ TOOLS BOOT MODE

→ MOTOROLA FREESCALE BAM

→ FCA CONTINENTAL GPEC4

 

• BAM SPC5674 CONTINENTAL GPEC4LM FCA Pinout

Connect with the multifunction cable the CNF1 signal on the PCB.

Use the driver:

→ TOOLS BOOT MODE

→ MOTOROLA FREESCALE BAM

→ FCA CONTINENTAL GPEC4LM

Foxflash read EDC16C66 in boot mode Success:

BOSCH EDC17 C66 [ TC1793 INT.F.] – Mercedes Benz

Step 1: Read and Write ECU

Connect with the multifunction cable the following pinout and the boot shown below.

Use the driver:

→ TOOLS BOOT MODE

→ INFINEON TRICORE Boot

→ SAK TC1793

Step 2: Password Search

Disable the boot mode by unsoldering the grey wire. Connect the pinout below.

Use the driver:

→ TOOLS BOOT MODE

→ INFINEON TRICORE Tool Password

→ PASSWORD BFT

→ Click on “Find Password” and follow the foxflash software messages.

Now that the password has been found, and it’s possible to read and write the control unit as described in STEP 1.

 

Everything received with fedex with no problems at all

Foxflash will read, write and clone PSA MEV17.4.2 in both Bench and boot mode. It will do auto checksum.

Foxflash MEV17.4.2 bench pinout

To read and write use the following driver:
→ BENCH TRICORE
→ CITROEN / PEUGEOT
→ TC1767 – PSA
→ MEV17.4.2

Foxflash MEV17.4.2 boot pinout (Tricore version is 1796.)

To read and write use the following driver:
→ BENCH TRICORE
→ CITROEN / PEUGEOT
→ TC1767 – PSA
→ MEV17.4.2

Many tools can read and write on bench without opening, ktag, kess v2, fgtech.

But many reported there is a risk to brick ecu with ktag clone if do it on bench, better in boot mode.  Foxflash with no risk.